Call Today

 

We've uncovered this great article involving How to Install a Bathtub directly below on the internet and believe it made sense to relate it with you on this page.

Mounting a bath tub isn't specifically rocket science, yet it does need strong plumbing, woodworking, and also in some cases, tiling abilities. Changing an old tub with a new one is additionally a reasonably challenging project. If the old bathtub is easily easily accessible, the job can relocate speedily; if you need to open up a wall to eliminate the old bathtub and place the brand-new bathtub, the task is much harder. In either instance, the task is within a home handyman's abilities, although you will certainly need a helper to leave the old bathtub and also set in the brand-new one. See to it you have actually certified on your own for the work and also fit trying it. As opposed to working with a contractor to take control of a halfway-completed task, it is far better to think about utilizing one before you start. Opportunities are you may need a specialist plumber to make tube links.
This post will aid you set up a new bath tub in your shower room if you have already purchased a brand-new bathtub and do not require to alter the setup of your previous water supply pipelines.
Your devices and also material checklist need to consist of the following:

 

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Knife


• Tape Measure


• Pipe Caps


 

Removing Old Touches

If you require to replace old taps with new ones as a part of your installment, after that the first thing you should do is disconnect the water system. After doing so, activate the faucets to drain pipes any water remaining in the system. The process of removing the existing taps can be quite bothersome due to the restricted access that is commonly the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the taps. Have a cloth all set for the remaining water that will originate from the pipelines. As soon as the supply pipes have actually been gotten rid of, make use of the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single faucets from turning during this procedure. When the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing substance.
Before carrying on to fit the new taps, contrast the pipe links on the old taps to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the brand-new taps to fit.

 

 

Fitting New Taps

If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic connector to avoid damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the other end provides a connection to the existing supply pipes.
If you need to fit a monobloc, then you will require decreasing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, position the tap in the placing opening in the bath/basin making certain that the washing machines are in place in between the faucet as well as the sink. Secure the faucet in position with the producer provided backnut. As soon as the tap is securely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with typical tap connectors. The former kind ought to be attached to the faucet finishes initially, tightening only by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been linked.

 

 

Mounting the Bathtub

Utilizing both wooden boards under its feet, put the tub in the called for position. The wooden boards are handy in evenly spreading the weight of the tub over the location of the boards as opposed to concentrating all the weight onto 4 small points.
The next goal is to ensure that the bathtub is leveled all round. This can be achieved by checking the spirit level and adjusting the feet on the bathtub till the level reviews degree.
To set up taps, fit the bottom of the outermost adaptable tap connector to the appropriate supply pipeline by making a compression sign up with; then do the same for the various other tap.
Switch on the water supply as well as inspect all joints and new pipework for leakages and also tighten them if needed. Fill up the bathtub as well as likewise check the overflow outlet and the regular electrical outlet for leaks.
Finally, fix the bathroom paneling as described in the producer's user's manual. Tiling as well as securing around the tub should wait up until the bathtub has actually been utilized a minimum of once as this will settle it into its last position.

 

 

Getting ready for the Installment

First of all, the sustaining structure provided with the bathroom should be fitted (if needed) according to the maker's guidelines. Next off, fit the taps or mixer to the bath tub. When suitable the faucet block, it is important to ensure that if the tap includes a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the taps device to avoid pressure on the bath tub.
Fit the versatile tap connectors to the bottom of both taps using 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet via the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you use all of the supplied washers.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom must now prepare to be suited its last placement.

 

 

Tiling Around the Bathtub

In the area where the bathroom fulfills the ceramic tile, it is essential to secure the joins with a silicone rubber caulking. This is essential as the fitting can move sufficient to split an inflexible seal, creating the water to penetrate the wall surface between the bathroom and also the tiling, causing problems with moisture as well as feasible leakages to the ceiling below.
You can choose from a selection of coloured sealants to assimilate your fixtures as well as fittings. They are offered in tubes and cartridges, as well as can securing voids up to a width of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of drenched paper or soft rope. Bear in mind to always load the bath tub with water before securing, to enable the movement experienced when the tub remains in usage. The sealer can fracture rather very early if you do not consider this movement before securing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally easily available on the market. It is recommended to fit the tiles using water-resistant or water-proof glue and also cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

We are very curious about A Step-by-Step Guide to Installing a Bathtub and I am assuming you appreciated our blog posting. Remember to set aside a second to distribute this blog post if you appreciated it. Kudos for your time. Please check up our website back soon.

Drips? Dial fast!